| ID | Subject |
| 2527 | GA-5EXSH PCI-X Compatibility Table ...More |
| 1762 | Why do I see "Broadcom BCM5751 Driver" item in the GS-SR295/GA-9ILDR driver auto run setup menu ? ...More |
| 1565 | Why does the system only show 3.5 GB of memory when I set 4GB memory on the motherboard. ...More |
| 1564 | How to configure onboard SCSI RAID on GA-9ILDR/GS-SR295 models? ...More |
| 1563 | How to configure onboard host RAID on GS-SR147S, GA-8IKHXT/8IKHDW models ? ...More |
| 1562 | How to configure onboard host RAID on GS-SR125E/222E/326E/275,GA-8EGXDRE/7A8DRH/9ITDW ? ...More |
| 1186 | How to installled DDR333 memory modules on SR-295 server? because I can't boot on DDR333 memory modules but can be work on DDR266 memory modules. ...More |
| 1185 | How to installed DDR333 memory modules on GA-9ILDR motherboard? becuase I can't boot on DDR333 memory modules but can be work on DDR266 memory modules. ...More |
| 1184 | SR-125ED support RAID 5 function. ...More |
| 1183 | Why I can't find GA-8IPXDR-E guide to Power LED connector from manual? ...More |
| 1182 | GA-8IPXDR-E server board and Intel SCRZCR/ Intel Zero Channel RAID controller fine on initial installation, after updating firmware, it get "System Check Error ID:166" on Winodws 2000 server. ...More |
| 1181 | When I install Intel Xeon 3.2GHz/533 FSB L3=2MB CPU, system will hang up during post screen. ...More |
| 1180 | When USB device is installed, it can't be recognized properly. ...More |
| 1179 | What kind of CPU can be supported on GA-8IPXDR? ...More |
| 1178 | Does a GA-8IPXDR support Intel RAIDIOS or Adaptec 2000S ZCR card? ...More |
| 1177 | Does SR147L server IDE device can be change for SATA device type? ...More |
| 1176 | Why I can't install O.S. on SR-125ED server through single hard disk without RAID function? ...More |
| 1175 | How to identify SR125E serverboard/bridge board/ backplane board version? ...More |
| 1174 | What is the difference between SR125 A4chip & B0chip? ...More |
| 1173 | Can I use the latest model 10 XP of AMD CPU under GA-7DPXDW series ? ...More |
| 1172 | Compatibility issue between the hard drives and backplane board IDE connectors of GS-SR114 ...More |
| 1171 | Apacer DDR PC2100 CL2.5 / ECC Issue ...More |
| 1170 | GBT Customer Letter To Address 8IPXDR/RedHat LAN Issue ...More |
| 1169 | What type of AMD CPU that support for Dual Processors? ...More |
| 1168 | Does the 7DPXDW motherboard only support Registered DDR RAM? I use 1 x Unbuffered DDR DIMM in any DIMM Slot (4 Slots had been tested) but the speaker beeps 1 second and stop 3 seconds; then beep-warning sound is going on. Is the problem of DIMM? Or, the system BIOS only support Registered DDR? ...More |
| 1167 | Can I use 300 watts power supply for GA-7DPXDW server board? ...More |
| 1166 | Unable to run the system when install Red Hat 7.1 and 7.2 for Adaptec 7899 ...More |
| 1165 | We have a 6ETXDR motherboard with two PIII 1200 MHz/256/133 CPUs installed, the motherboard is currently hanging when two CPUs are installed into the board. Only one CPU works functionally. (1200Mhz/256/133 cpu is being used) How to reslove this problem? ...More |
| 1164 | We tested the GA-6VTXDR-C with two Celeron 1.2/256/100/1.475 and we found out that the motherborad was switched on but only recognized a single CPU after 2 or 3 seconds. No problems with testing dual PIII.
...More |
| 1163 | We tested the GA-6VTXD with two Celeron 1.2/256/100/1.475; unfortunately the motherboard can not be switched on. There will be no problems if using only a single CPU.
We also tested it with double PIII and had no problems. Does it normally work with dual Celeron 1.2 or higher? ...More |
RSS